Monthly Archives - September 2017

SAFECORE VC

SOLVENT FREE ULTRA CHEMICAL RESISTANT VINYL ESTER BASED COATING FOR INDUSTRIAL FLOORS AND STEEL SURFACES

DISCRIPTION

SAFECORE VC is rapid curing, 2 pack Vinyl Ester based coating with outstanding resistance to aggressive acids, solvents and alcohols and other chemicals. This product is designed where high chemical resistance is of primary requirement. Due to its high molecular weight and low permeability, it will withstand exposure to a broad range of acids, caustics, and solvents. SAFECORE VC is designed for coating primary and secondary containment, trenches, troughs, pump pads, equipment, and structural members.

BENEFITS

• Excellent resistance to a wide range of chemicals.
• High temperature performance; in many cases up to 350°F (spills) or 400°F (dry heat).
• Excellent adhesion to steel & concrete.
• Vary rapid cure, even at low temperature.
• Hygienic and easily cleaned.
• Tough durable and abrasion resistant.
• Slip resistant options.

USES INCLUDE:

• Can be used as an internal lining for concrete or steel storage tanks.
• SAFECORE VC is designed for coating primary and secondary containment, trenches, troughs, pump pads, equipment,
and structural members.
• For chemical resistant floor/wall coating for chemical and printing works, bottling and canning factories, pharmaceutical production etc.

INSTRUCTIONS FOR APPLICATION

Surface Preparation:

Steel – The surface should be free of oil, grease, dirt, mill scale, rust, corrosion products, oxides, paint and other foreign matter. In absence of blast cleaning, prepare the metal surface by wire brushing, sanding. The surface should be pretreated with emery paper or all rust should be removed with SAFECORE RR.

Concrete Surface: Concrete shall be minimum of 21 days old and/or residual moisture content shall be below 6%. Ensure that the concrete is clean and free from dust, laitance oil, curing compound, existing paint finishes etc. Blow holes and defective concrete should be made good using a proprietary void filler FAIRSCREED VF.

APPLICATION PROCEDURE:

The following application procedure should be followed:

PRIMER COAT(SAFECORE VC PRIMER) :

MIXING : SAFECORE VC PRIMER is supplied as ready to use in pre-weighed packs of base and hardener for easy application on site mixing. Pour the hardener into base cane, mix well using paddle attach to an electric drill until uniform colour is produced.

APPLICATION PROCEDURE : SAFECORE VC PRIMER may be applied by brush , roller or airless spray to give continuous coating on prepared surface. After proper surface preparation apply one coat of SAFECORE VC PRIMER and allow it to dry completely.

NOTE ; For technical details refer the Separate Technical Datasheet of SAFECORE VC PRIMER.

SECOND COAT(SAFECORE VC) :

MIXING : SAFECORE VC is supplied as ready to use in pre-weighed packs of base and hardener for easy application on site mixing. Pour the hardener into base cane, mix well by chemical means until uniform color is obtained.

APPLICATION PROCEDURE : When primer dries completely apply one coat of SAFECORE VC . SAFECORE VC may be applied by brush , roller or airless spray to give continuous coating. After application allow it to dry completely. For slip resistant finish broadcast SAFECORE ANTI-SLIP GRAINS immediately after first coat application. After proper curing( at least 10 hrs) brush off excess aggregate and apply Second final coat of SAFECORE VC.

CURING: Allow to cure for minimum of 12 hours @300C for light foot traffic and 24 hours prior to vehicular traffic. Allow a minimum of 3 days cure at 300C for optimum chemical resistance.

CLEANING : Tools and mixers should be cleaned with SAFECORE TOOL CLEANER immediately.

PACKING & COVERAGE : SAFECORE VC is available in 1Kg & 5Kg packing . A 5Kg pack is sufficient to coat 5-6m2 of surface with the 1 coat treatment with DFT of 150-200 microns.
SHELF LIFE & STORAGE: SAFECORE VC will have a shelf life of 3 months in unopened containers when kept in a dry condition at temperature between 50C to 450 C. Storage at higher temperature or high humidity may reduce shelf life.

FAIRSCREED TG (WB)

Two Component Water Dispersible Epoxy Based Acid & Chemical Resistance Tile Grout

DESCRIPTION
FAIRSCREED TG (WB) is a thixotropic, Two Pack Water dispersible Epoxy based tile grout ideal for all type of tile joints. FAIRSCREED TG (WB) is a V.O.C. free product, so it is Eco friendly. Also it provides excellent adhesion even under Damp Condition. Tile gap width of 10 to 50 mm gap can be filled easily with FAIRSCREED TG (WB).

BENEFITS

• Excellent resistance to Water, diluted acids & other chemicals
• Excellent adhesion to damp surface and green concrete
• Thixotropic in nature, so suitable for application in both Vertical & Overhead locations.
• V.O.C. Free Product
• Early development of hardness
• Low Odor
• Rapid curing
• Cost Effective and Eco-friendly

RECOMMENDED USES
• FAIRSCREED TG (WB) is a Water Base Epoxy paste adhesive particularly suitable for all types of Tile Joints.
• FAIRSCREED TG (WB) can also be used for thin section concrete repairs.

APPLICATION INSTRUCTIONS
Surface Preparation: Substrates (tile joint) should be sound, clean and free from dust, dirt, grease, oils and other contaminants. A roughened or profile surface will ensure optimum adhesion.

Mixing: The Base and Hardener components should be mixed thoroughly using a stiff spatula or slow speed drill with paddle attachment, until a uniform colored mixture is obtained.

Application: The application of FAIRSCREED TG (WB) is best using Spatula, Trowel, Serrated trowel or Stiff bristled brush depending on the gap of joint to be treated.

PACKING AND COVERAGE

FAIRSCREED TG (WB) is supplied in 1Kg & 5Kg Pack. 1 kg of FAIRSCREED TG (WB) covers 13-15 running feet at 5mm x 5mm groove size.

FAIRMATE WALL PLASTER

A READY TO USE POLYMER BASED WALL PUTTY

Description

FAIRMATE WALL PLASTER is a polymer based Off- White colored wall putty. It has excellent adhesion on any cement surfaces.

Benefits

1. Excellent adhesion.
2. Excellent thixotropicness.
3. Excellent bonding & finishing.
4. No curing is required.
5. Excellent consistency hence suitable for application.
6. Can be used in Interiors.
7. Cost-effective.
8. Easy to apply.
9. By using FAIRMATE WALL PLASTER less coats of FAIRCOAT of certain color needed to apply. Almost replaces the
application of Primer Coat.
10. It has an excellent coverage of 11 Sq. Ft. per kg of the product.

Recommended Uses

1. FAIRMATE WALL PLASTER is suitable for use on both precast and conventional building areas on new internal
surfaces of precast concrete, sand cement plaster etc.
2. Can be used as putty before applying FAIRCOAT of related color. E.g. Off White
3. Can be used in Interiors and Exteriors.

Application Instructions
Surface Preparation :

The surface for the application should be absolutely dry. There should be at least 10 days gap before FAIRMATE WALL PLASTER is applied for newly plastered surfaces. Remove all loose material and wipe off the powder with cotton cloth.

Application :

Apply FAIRMATE WALL PLASTER with painter’s putty knife or mason’s steel trowel on the surface. Allow to dry it completely and rub the surface with emery paper No. 320. The loose powder on surface should be wiped off with cotton waste.