Yearly Archives - 2017



ROADCRETE MACADAM is a single part bitumen based road repair mortar composed of a factory controlled fully graded hard stone material, fine aggregates, formulated bitumen contains and special additives. It is a fast curing, high strength trowel applied mortar designed for instant rapid mortar. Its
rapid set characteristics allow a fast return of the road to traffic. The product is chloride free and can be safely used in contact with reinforcing steel. This material is capable of being applied in wet condition where the temperature ranges from 5 0 C TO 500 C.


• Excellent bond to concrete substrate
• Extremely low permeability provides protection against carbon dioxide and chlorides
• Rapid repair time
• High strength
• Fast setting
• Easy to use
• Cost effective instant road repair mortar
• Open for the traffic for shortage timing
• Can be used for man hole cover
• It will not peel, crumble, dust or crack
• Permanent repair to spelled & damaged concrete
• Freeze thaw durability better than standard concrete
• Minimum labour required.


ROADCRETE MACADAM is conforming to requirement of ASTM D- 1664 and ASTM D-2027 modified as follows.
Flash point 790 c mini.
Sybolt furol viscosity at 600 c 200- 500 sec
Water 0.2% maxi.
Distillate test To 2250 c: None
To 2600 c 0-15%
To 3150 c 15-75%
Residual at 3600 c 73-90%
Residue tests:
Penetration at 250 c 150 -300
Ductility at 250 c 100 cm minimum
Solubility in trichloroethylene 99 % minimum

Permanent reinstatement of opening in carriageways, footways, cycles paths, private drives, reinstatement of pot holes. Remedial repairs around manholes.

LYING: Minimum thickness 15 mm.

CURING: No curing is required.

COVERAGE: The depth & width of pothole, crack, utility cut etc. will greatly influence the coverage rate achieved.

CLEAN UP: All tools should be cleaned immediately after use with a solvent base cleaner such as paint thinner or mineral spirit.


1. Bleeding: Is the flushing of the asphalt binder to the surface of the patch. IT caused by a combination of traffic loads, insufficient voids in the mix, or too much binder in the mix. Bleeding may cause poor skid resistance. – The use of open (gap) gradation and lower binder content should keep bleeding to a minimum.

2. Dishing: Is the further compaction of the patch under traffic loads. It is the result of material instability and inadequate compaction during the placement of the material. Compatibility is related to workability. Mixes with poor workability is difficult to compact. To determine the amount of dishing, a 1-m metal bar was placed across the patch parallel with the direction of travel. The amount of dishing was measured with a ruler accurate to 1.5 mm in the centre of each quadrant. The ratings were determined from the depth measurements.

3. Debonding: Occurs when the patch material loss its adhesion to the pavement at the bottom and/or sides of the pothole. When debonding occurs, the patch material can be pulled out of the hole by traffic, so the patch fails. It can be determined by disintegration i.e. the cracking cause at the edge of the patch for each quadrant. Missing patch was evaluated as a large scale loss of material. In some cases, these appeared to the cohesion failures rather than adhesion failures as all of the remaining particles were fully coated.

4. Raveling: is the loss of aggregate form the surface of the patch. Raveling is cause by stripping, poor cohesion, excessive fine aggregates and poor aggregates interlock of the patch material.

5. Pushing and shoving: is the vertical or horizontal movement of the patch material in the pothole.

The behavior of the ROADCRETE MACADAM in the above testing is very good.


The workability of the mixture was examined using the pennsylania transportation institute/ strategic highway research program (PTI / SHRP). For the PTI test, the sample is loosely placed in a 102 mm cubical box with a 10 mm hole centered on one side. A soil penetrometer with a round nose adapter 10 mm in diameter is pressed through the hole into the material. The value from the penetrometer is recorded as the workability reading.

The workability of the material was evaluated after they had been stored for 6 months as a measure of their storage ability.

The ROADCRETE MACADAM results of the workability surveys are good.
The evaluated at 7 and 14 days and 1, 3, 8, 9 and 12 months after placement.


ROADCRETE MACADAM is supplied 25 kg packs A 25 kg pack yields 12.5 ltr of mortars sufficient for 0.75m2 @ 25 mm thick.



1. Gives a textured finish
2. Anti-carbonation properties
3. Good weathering properties
4. Excellent bond.
5. Forms tough acrylic plaster
6. Allows substrate to breathe
7. Choice of colours
8. Single pack, Trowel applied
9. Non toxic/Non flammable
10. Excellent waterproof coating


FAIRCOAT SCREED is ready to use acrylic based screed containing special polymers and fillers. It is a textured protective, decorative anti-carbonation screed for interior and exterior surfaces with exceptional weathering characteristics.

Recommended Uses

FAIRCOAT SCREED is used to provide a textured decorative durable coating for concrete and masonry surfaces. One coat application is recommended with a thickness of 1.5 to 2 mm.

Application Instructions

Surface Preparation :
Substrates must be clean, sound and free from dust and loose particles. All holes and cracks must be filled with a suitable filler. All traces of oil, grease or other contaminations must be removed. The new concrete surfaces must be atleast 14 days old before coating. If in doubt, allow full curing to take place for 28 days before application of FAIRCOAT SCREED.

Priming :
On old or porous surfaces, ensure that the substrate is sound and free from any loose particles. Apply FAIRCRETE SBL, apply FAIRCOAT SCREED on the primed surface.

Application :
Stir the material in the container thoroughly and spread evenly with trowel. Avoid application during rainy weather. The surface texture and porosity must be taken into account while estimating quantities.

Cleaning :
Tools should be cleaned immediately after use with water.




• Liquid Application, easy to apply
• White Color Membrane.
• High build properties ensures rapid application.
• High elasticity, ensuring a permanently flexible barrier over a wide range of temperatures.
• Thermal Stability.
• Screeding can be done easily over applied membrane after complete curing.
• Suitable for Exterior application e.g. Terrace
• Good bond strength.
• For Extended Life Waterproofing, application with GRS (Glass Reinforcement Sheet) is recommended.
• Excellent adhesion.
• Good Crack bridging property.
• Can be applied to range of substrates.
• Outstanding resistance to brittlement and oxidation.

WATERGUARD LIQUID MEMBRANE (WHITE) is a single component White colored is a highly elastic tough waterproofing system based on special co-polymers & fillers. WATERGUARD LIQUID MEMBRANE (WHITE) is highly resistant to aggressive soils and soluble salts providing an effective continuous barrier and protection against water borne damage.
WATERGUARD LIQUID MEMBRANE (WHITE) is ideally suited as vapor/salt barrier to building facades behind granite, marble, stone cladding, and curtain wall elements.

• Useful as protective coating on concrete and brick foundations, retaining walls, timber etc.
• Provides a sandwich membrane in new construction and surface treatment on existing slabs.
• Provides a key for plaster on difficult surfaces.
• For waterproofing and protection of structure, concrete, columns and beams.
• Used for the external insulation of foundations, underground constructions, basements. etc.
• Used for insulating water leakages in closed damp environments such as bathrooms, kitchens, toilets, etc.
• Service life can be further extended by using GRS (Glass Reinforcement Sheet) in application.
• WATERGUARD LIQUID MEMBRANE (WHITE) is particularly suitable for a wide range of applications including wet
areas, foundations, basements, terraces, retaining walls, bridge abutments, planters, inverted roofs and
remedial repairs to felt, asphalt, concrete, fibreous cement or other roof structures when protected from
exposure to direct.


No especially skilled person required for its application. It provides a seamless insulation layer. As a water-based material it is environment friendly. Because it contains water, it enables good adhesion even when the surface is moist. It provides permanent elasticity. It is ready to use. Cold applied material, it does not require heating or thinning. It can normally be applied by brush. Very much useful for Waterproofing purpose.


SURFACE PREPARATION : All substrates must be sound, clean,dry, smooth and free from protrusions, voids, honey-comb, sand high spots. Presence of curing agents, paint and oil will impair adhesion.
Moss and lichen must be removed and area treated with proprietary fungicidal wash to kill spores and inhibit further growth. Following treatment wash area thoroughly with Clean water and allow drying. Fillets must be provided at corners or sharp angles using 4:1 sand and cement mortar modified with a good quality bonding agent FAIRCRETESB(L).

PRIMING : Priming is not normally required on good quality, well prepared substrates.

APPLICATION : WATERGUARD LIQUID MEMBRANE (WHITE) should be applied by brush to obtain a continuous unbroken film. Four coats are required to achieve a better performance. Each coat should be applied after proper drying of previous coat. For application with GRS (Glass Reinforcement Sheet), first of all apply one coat of WATERGUARD LIQUID MEMBRANE (WHITE) then after put GRS (Glass Reinforcement Sheet) on applied material & sheet should be spread when first coat is Wet. After spreading GRS (Glass Reinforcement Sheet) roll the Paint roller over it to ensure that sheet is bonded with applied material & no air pocket has been left in between contact of applied material & GRS (Glass Reinforcement Sheet). After that apply remaining subsequent coats of WATERGUARD LIQUID MEMBRANE (WHITE) over it. WATERGUARD LIQUID MEMBRANE (WHITE) must be protected from mechanical damage during subsequent construction or backfilling works. Any damage may be repaired by spot application. If a water flood test is to be run, the membrane should cure for a minimum of 10 days. Whilst WATERGUARD LIQUID MEMBRANE (WHITE) is resistant to frost, adhesion will be impaired if applied to frosted substrates. Application should be avoided if substrate temperatures are below 5ºC or rain is imminent.
On Exterior application, applied material may become Bone White after an instant of period but this will not affect or alter the performance of WATERGUARD LIQUID MEMBRANE (WHITE).

Cleaning : Application equipment should be thoroughly cleaned after use with Water. Spillages should be absorbed with sand, vermiculite or similar and be disposed of in accordance with local regulations.


WATERGUARD LIQUID MEMBRANE (WHITE) is supplied in 1kg, 5 kg, 10 kg & 20 kg pails. It has coverage of around 1.1 kg/m²@1 mm thickness.

Coverage rate will vary with substrate condition and profile

For more details, Contact at Ph.: +91-265-2331193, WhatsApp : +91 7574834603 Toll Free: 1800 12345 34

Visit E-mail:


Although crystalline waterproofing technology has been around for more than 50 years, it is still considered “state-of-the-art” and has only recently been embraced by the construction industry as a superior replacement for conventional membranes. Used in virtually every country around the world, integral crystalline waterproofing has been repeatedly and successfully tested.

Crystalline waterproofing systems rely on a revolutionary crystalline technology that turns porous concrete into an impermeable barrier. The result is a structure with reduced cracking, self-sealing and waterproofing abilities which provides a powerful defence against water damage and corrosion of reinforcing steel.
Whether it is new construction, upgrading an existing structure or repairing cracks, this technology will help you build quality, reliability and cost-effectiveness into the concrete.

Crystalline Waterproofing Advantages

√ Replaces unreliable exterior membrane systems
√ Penetrates deep into concrete—many inches over time
√ Self-seals hairline cracks—minimum .5 mm (.02 in.)
√ Reactivates in the presence of moisture—even years later
√ Effective against hydrostatic pressure—up to 140 m (460 ft) of head pressure
√ Waterproofs from any direction (i.e. positive or negative side)
√ Impervious to physical damage and deterioration
√ Easy to apply and reduces potential for human error

How Does It Work?

Unlike old-fashioned external membranes, which rely on an additional hurdle to shield the concrete from moisture, crystalline waterproofing product actually transforms the concrete into a water-resistant barrier. It becomes an integral part of the concrete matrix when applied to existing concrete or added to the mix at time of batching. When combined with water and concrete, the product reacts with un-hydrated cement particles to form millions of needle-like crystals. Over a period of weeks and months, these crystals grow, filling the naturally occurring pores and voids in concrete, and permanently blocking the pathways for water and waterborne contaminants.
Later, if cracks form due to settling or shrinkage, incoming water triggers the crystallization process and additional crystals begin to grow. The crystals fill the cracks and ensure that the structure’s waterproofing barrier is maintained and protected. In other words, the product has the unique ability – even years later – to self-seal hair-line cracks before they turn into costly cracks in your budget.

How are the Products applied?

Crystalline waterproofing products are supplied as a dry powder comprised of Portland cement, silica sand and special chemicals. For new construction it can be added to the concrete mixture at the plant or on-site; applied as a dry-shake and towelled into fresh concrete surfaces; or brush-applied in slurry form to existing concrete. In addition, the products can be used to repair concrete cracks and waterproof construction joints in grout (dry pack) form.

Where Is It Used?

Crystalline waterproofing products have proven their versatility in hundreds of projects across the globe. They have been incorporated in high-rise office towers, commercial buildings, parking structures, elevator pits, subway tunnels, and mountain pipelines. They have demonstrated their reliability in protecting water supply in reservoirs and treatment tanks, recreational facilities such as pools and spas and the supporting structures of bridges and dams. These products can provide permanent waterproofing in a wide range of applications and environmental conditions.

Crystalline Waterproofing will reduce cost!

Cost savings – materials
Savings can be realized immediately through the elimination of strengthening agents, water reducers, plasticiser, curing agents, air entrainers, set retarders and shrinkage compensators. One of the largest immediate savings is the elimination of external waterproofing membranes which require both the purchase of waterproofing membrane and labour costs.

Cost savings – Labour
The ability to increase pumping, pouring, finishing and cleaning efficiency through increased flow ability and ease of use will also provide immediate labour cost savings. This technology dramatically increases productivity by reducing the labour demands and increasing the speed of the construction.

Cost savings – Job
A few simple calculations can be utilized to determine the dramatic savings that can be realized through the elimination of additives and externally applied water proofing membranes. The simple use of one additive can actually increase productivity while reducing costs.

Cost savings – Repair
The simplicity in using crystalline waterproofing products also eliminates errors due to incompetence and neglect as it is applied directly to the ready mix truck or at the batching plant. When using these products with a ready mix truck, the required amount of is added and allowed to mix for 10 minutes. The concrete is then ready for pumping and placing. The ease of use will eliminate the inconvenient and costly necessity of repairing somebody’s mistake.

Cost savings – Long Term
The long term cost savings are extremely impressive. The ability of crystalline waterproofing products to strengthen a concrete structure, to permanently waterproof and to protect reinforcing steel from corrosion and pollution increases the life expectancy of concrete structures. This will reduce the need for costly repairs and restoration in the future. It is not difficult to understand the savings advantage that can be achieved in the long run through the simple addition of crystalline products to concrete. The savings include labour, equipment, materials, financing, and the opportunity costs involved when a repair, restoration or rebuilding of a structure is required.

Integral crystalline concrete waterproofing admixture – FAIRCRETE RMW CRYSTALLINE

This product eliminates the need for conventional external waterproofing membranes. It saves time, money and hassle at the construction site over the lifetime of the concrete. The crystalline admixture is available in pulpable bags for easy addition to the concrete mixer. It won the ‘Most Innovative Product’ award from the World of Concrete tradeshow. In addition, it is the first concrete admixture to be certified by the International Code Council – Evaluation Service (ICC-ES) as a Chemical Admixture used in Concrete (AC198). This chemical admixture is used for the treatment of concrete and concrete products to protect against water intrusion, leakage, cracking, chemical attack, and corrosion of reinforcing steel.

Specially designed chemical admixtures are available for waterproofing cementitious mortar. It contains a unique blend of chemicals that react with the cementitious materials in the mortar to form hydration crystals, blocking water intrusion.

Liquid, membrane-forming compounds are also available for curing concrete. The liquid helps to prevent the rapid evaporation of moisture from fresh concrete to allow more complete cement hydration and to dramatically reduce the occurrence of drying shrinkage cracks. It is water-based and is a suitable replacement for wet curing in conformance with ACI 308 guidelines.

Surface-Applied Concrete Waterproofing Products – WATERGUARD CRYSTALLINE

Recently built structures and heritage buildings need water protection too! Whether you’re waterproofing a new structure or repairing leaks, concrete waterproofing treatments allow you to turn existing concrete into a waterproof barrier reliably and cost-effectively.

Repair & Maintenance Systems – WATERGUARD T CRYSTALLINE

No matter how carefully you build and maintain your concrete structure, it’s not a matter of if cracks will occur, but when. At best, concrete cracks are an unattractive nuisance. At worst, they lead to leaks that can damage the interior of the building, corrode steel reinforcements, and ultimately shorten the life of the concrete structure.
Unlike other systems, the repair and maintenance products that are available, protects from any direction. Even against high water pressure. Because they can be applied to either side of the concrete, there are no limits when it comes to repairing or waterproofing hard or impossible to reach areas. These products can be put to work wherever the cracks are—without expensive, time consuming perimeter digging.

How does Crystalline Waterproofing Technology work?

This technology is an integral crystalline concrete waterproofing system that was developed over 30 years ago. When added or applied to concrete, crystalline chemicals cause long, narrow crystals to form. The crystals penetrate through the concrete and fill the pores and hairline cracks. The crystals continue to react with incoming water to self-seal cracks that inevitably develop in concrete over time. This technology protects concrete structures against water and contaminants that can weaken or destroy concrete and corrode steel reinforcements.

Where is it used (types of jobs)?

Crystalline waterproofing systems can benefit any concrete structure at risk of water penetration. Its self-sealing ability and resistance to high water pressure makes it ideally suited for below-grade foundations, parking lots, elevator pits, water containment and aquatic facilities, bridges, dams, tunnels, and pipelines. Integrated – Crystalline waterproofing penetrates into the concrete. It will not crack, peel, tear or wear-away.

 Continually self-seals – Crystals within the concrete reactivate repeatedly over time to reseal cracks and prevent water penetration.

 Environmental – The products are non-toxic, non-flammable and odorless. This allows the concrete to be recycled. Traditional membrane systems are petroleum-based. They use adhesives with highly volatile organic compounds. The vapor from these compounds can cause respiratory problems and contribute to “sick building syndrome”. Oil can also leach out and contaminate ground water.

 Maximizes space – No additional space outside the structure is required for membrane application. This allows for a larger structural footprint and building right to the property line.

 Saves time – The products can be applied to green concrete or added to the ready-mix truck. There is no need to wait for the membrane application, so backfilling can begin right away.

 Tropical climates – Membrane systems become brittle and deteriorate when exposed to prolonged heat. Crystalline systems reduce premature moisture loss in hot or tropical climates. It creates a more durable structure and reduces shrinkage and cracking. It is unaffected by climate and remains effective for the life of the structure.

How is our crystalline technology different from other crystalline technologies?

Many products claim to have permanent waterproofing abilities. Most are only damp proofers and have little penetrating ability. These products contain stearates or sodium silicates. They waterproof by filling initial surface pores of concrete only. Therefore, they work well initially, but continually deteriorate over time.
Our products are free of stearates, sodium silicates and chlorides. It contains a proprietary blend of chemicals that cause hydration crystals to grow throughout the capillaries and pores of concrete as the material comes in contact with moisture. The crystals continue to react in the presence of later, making our products more effective with time.

For more details, Contact at Ph.: +91-265-2331193, WhatsApp : +91 7574834603 Toll Free: 1800 12345 34

Visit E-mail:




• Easily applied water repellent treatment giving a self-cleaning, hydrophobic surface to masonry, concrete
and asbestos sheeting.
• Excellent water repellent
• Excellent resistant to UV light.
• Minimizes efflorescence and prevents growth of fungus.
• Economical and very easy to apply
• Prevents entry of moisture into the walls, but allows the surface to breathe.
• Colorless hence maintains natural color of walls.


WATERREPELL S is a ready to use, silane-siloxane based repellent which penetrates in concrete or cementitious substrates pores, providing an effective water repellent protective coating. Its UV resistant properties make the film durable for outdoor use. The use of silicone retards or prevents changes in the surface appearance by resisting the deterioration effects occurred due to atmospheric attack. Due to its excellent water repellent properties, dirt and other atmospheric impurities are washed off by rain and it’s clean appearance is maintained for a longer period. Also, WATERREPELL S prolongs the clear appearance of buildings and minimizes efflorescence.


WATERREPELL S is suitable for external application to exterior walls of brick or concrete blocks, cement renderings, asbestos cement, concrete and all types of stone, including limestone. Also used as an injection damp coarse fluid and provides a durable barrier to water penetration of porous surfaces.


• water Intrusion
• Salt Intrusion
• Weathering
• Spalling, Staining
• Efflorescence
• Fungi, Freeze-Thaw Scaling


• Architectural Concrete
• Structural Concrete
• Commercial Parking Garages
• Concrete Masonry Units
• Portland Cement
• Brick Masonry (non-glazed)
• Flagstones & Pavers (non-glazed)
• Limestone
• Sandstone

It is non-glossy and will not alter the color or surface texture of the natural substrate. This architectural grade sealer is 100% water vapor permeable and, unlike solvent-based products, is not hazardous. Water repellent S prevents moisture from seeping into concrete and also keeps damaging ice melting compounds from penetrating into concrete, making it especially ideal for use in parking garages where de-icing chemicals are required in order to protect from extreme moisture.


Surface Preparation: All surfaces to be treated must be sound, clean and dry. Any defects and cracks, other than hair line cracks, should be made good. Dirty surfaces should be thoroughly cleaned and organisms such as algae or lichens should be removed. In no circumstances should detergents be used as they may reduce the efficiency of the treatment. The surface should be allowed to dry before the application of WATERREPELL S. WATERREPELL S should not be applied over mastics surfaces Glass, etc. should be protected against splashing during application.
Application: WATERREPELL S is supplied ready to use. Apply by brush or low pressure spray. The WATERREPELL S should be applied liberally so that it runs freely down the surface to about six inches below the point of application. When applying by spray, the pressure should be kept as low as possible to avoid excessive misting, and the nozzle held close to the surface. After application of WATERREPELL S, it dries within a few hours and becomes fully resistant to water in 24 hours. Brushes, spray equipment, etc. may be cleaned with water.


Packing: WATERREPELL S is available in 1, 5, 10, 50,100 liters carboys.

Coverage: 1Ltrs of WATERREPELL S will cover approx. 4 to 5 m2 of surface depending upon porosity and surface texture. Normally one coat is sufficient.



FAIRMATE MICROCRETE is a Unique new age decorative product which suitable for application on Floors, Walls & even on ceilings. The Uniqueness of this product is that it can even be applied to create uniform surfaces with minimum possible number of joints. With the increase of the renovation market this product can be applied directly on existing coverings such as Ceramic Tiles, Mosaic Floors, Wood, Metal, Dry boards & Glass. FAIRMATE MICROCRETE is the product which is available in different color combinations & patterns. The surface finished with FAIRMATE MICROCRETE provides unique architectural look whether it has been applied in Living Room, bathroom, office or kitchen, industrial floor, furniture, external façade. FAIRMATE MICROCRETE can be easily applied upon existing coverings, such as ceramic tiles without removing them, allow us to quickly and easily change the look and shape of our space with low cost and in a short period of time.


FAIRMATE MICROCRETE can be applied as per below described surfaces:

• On internal floors and walls,bathrooms on cement based substrate on floors and gypsum boards on walls.
• On external floors and walls, staircases and external whirlpools.
• On Internal floors and staircases over existing ceramic tile floors.
• On Internal floors and walls over existing ceramic tiles.
• On floors, walls and staircase inside swimming pools.
• Suitable on marble and porcelain sink, office, flower. pot, office, kitchen bench, heating panel and office
produced of cement board.


• Small application Height.
• High Tensile & compressive strength.
• Available in Variety of Colors & Patterns.
• Can also be applied on existing coverings such as Ceramic Tiles, Wood, Dry Board, Naval Board, Glass etc.
• Available in Variety of Varnish coat finishes.
• Ease of application.
• Excellent bonding on variety of substrates.
• Suitable for application on Floors, Walls & Ceilings.



Why do we need to use tile adhesive to lay tiles, what are the benefits?
SAND-CEMENT conventional way of tile fixing
• Sand cement composes of Ordinary Portland Cement (OPC) and sand. OPC is used for rendering and masonry while sand is normally river sand, which is hard to control grain size, cleanliness, and quality.
• Inconvenience to work with OPC comes in form of small bags and sand must be bought in huge quantity, which extensively occupy storage areas. OPC and sand must be relocated to another area for mixing and the process is dirty and dusty. Tiles need to be soaked in water for at least one day before being laid with sand-cement, and this is time consuming.

Tiles soaking in water

Time consuming and inefficiency

• To lay tiles with sand-cement traditional way is to apply the mixture of sand-cement in lump on tiles’ back so it has to be done with one tile at a time.

Aesthetic and de-bonding problem

• Without additive to help retaining water, mixture of sand-cement dries fast and then causes the difficulty to adjust the tiles after being laid. This leads to aesthetic problem of the line of tiles and also poor bonding strength, which will be the reason of de-bonded tiles later. Laying tiles traditional way by applying sand-cement mixture in lump at tiles’ back will create voids underneath the tiles and water can seep through. This creates white stain problem. Moreover, tile will be fragile at the area without any adhesive underneath.

Limitation of application

• Poor bonding strength of sand-cement mixture causes by dirt(mitti) in the sand and uncertain proportion of the mixture. Besides, there are limitations to use the mixture for laying following tiles in the following conditions.
• Low absorbent tiles
• Granito with 60 x 60 cm or greater size
• Glass mosaics – On polished substrates
• On existing tiles
• On substrates where subject to movement
• On the areas with high pressure and impact

Material wastage

Thick layer of sand-cement mixture must be used to lay tile traditionally in lump and/or to adjust the floor level, in order to gain its bonding mechanism. There will then be more loads onto structure. Moreover, there will be material wastage since the mixture dries faster than the application.


Tile adhesive is ready-mixed and specially formulated from special cement grade, selected fine sand, and additives to improve its essential properties for laying tiles. High performance tile adhesive can be used to lay tiles on existing tiles, on polished cement, on wooden substrates (with the use of primer), or on other special substrates.

Easy to use

It’s very easy to use tile adhesive, it will be already ready to use after just mixing with water. Bagging product makes it convenient for transportation process, providing low dust and clean working space. Tiles are not needed to be soaked, just un-box them and lay.


Notched trowel is normally and efficiently used to apply the mixture of tile adhesive on the area of about 1 m2. Tiles are then continuously laid onto notched adhesive and quickly adjusted into the lines.
Working quality
Optimum setting time of tile adhesive allows tiles to be easily adjusted within a certain period of time. It makes tiles being laid in line and gives the aesthetic final look. Applying tile adhesive with notched trowel provides full spread on back of tiles and will reduce many problems like broken tiles esp. on the corner, water seeping, and stain or efflorescent. Full contact of the adhesive on tiles’ back and substrate provides strong bonding strength and long lasting tiling work.

Variety of work

Tile adhesives are formulated according to specific applications such as to lay tiles, glass mosaics, large-size granito (up from 60 x 60 cm), to lay tiles on polished substrates, on dry wall system, on existing tiles without removing them, on external areas, parking areas, industrial areas, in swimming pools, and many more.

Economical reasons

Laying tiles by using tile adhesive with notched trowel requires less amount of material. Adhesive layer is a lot thinner than the mixture of sand-cement, and this leads to lighter load to building structure. A bag of 20 kg tile adhesive can be used to lay tiles on the average area of 4 – 5 m2. A bag of 25 kg tile adhesive can be used to lay tiles on the average of 6 – 7 m2. Area coverage depends on substrate smoothness, working tools, and skill of tilers.



• Fast and efficient
• Easy to use, only mix with water
• Better bonding strength
• Can be grouted within 24 hours without waiting for the moisture to evaporate
• Applicable on existing tiles, many special substrates like polished cement, dry wall system, etc.
• Thinner layer

• Higher price per bag
• Substrate needed to be proper leveled

Sand-cement Conventional way

• Cheaper
• Laying tiles and leveling at the same time

• Time consuming
• Tiles must be soaked
• Moisture can be accumulated beneath tiles
• Tiles are easily de-bonded
• Not applicable to lay low absorbent tiles like 60 x 60 cm granite or any larger sizes
• Not applicable to lay tiles on existing tiles, and on polished cement
• Not applicable to lay glass mosaics

FAIRFIX MORTAR confirms to IS 15477: 2004. It is approved by Bureau of Indian Standard vide ISI registration no. CM/L 3717363.

FAIRFIX MORTAR is composed of ordinary Portland cement properly selected & graded aggregates, polymer, rheology modifier & additives. It is used for fixing of ceramic tiles, glaze tiles, natural stones, etc. internally & externally over walls & floors with an added application of tile on tile because it gives excellent bond on cementitious surfaces like, concrete, plaster, etc. It forms a waterproof barrier between two surfaces and has excellent ‘grab’ properties of tiles to the substrate. It is specially designed for heavy-duty tile applications like granite, mosaic on internal/external vertical surfaces. Highly flexible adhesive also has an excellent waterproofing ability.

Areas of Application

• Permanent fixing of ceramic tiles.
• Fixing of insulating and acoustic boards.
• Swimming pool tile fixing.
• Large format tiles on internal/external applications.

Physical Appearance : Grey Powder
Mix ratio product: water parts : 3: 1 by volume
Open time@30 0C : 25 min
Adjustability time : 20 min
Trafficable time : 24 hrs


Waterproofing system provides protection to the structure from water ingress. The practice of waterproofing dates back to ages where the different techniques used were bituminous, metallic sheet, poly-urethane based and so on.

The modern techniques used in waterproofing include:

1. Crystalline Waterproofing System

The crystalline waterproofing system works in a system where there are certain insoluble crystals which block the water bearing capillaries. This is a cement based system and is commonly used for the terrace gardens, balconies, basements, bathrooms, water tanks and other water bodies.

2. Flexible Membrane Waterproofing System

There are two main components involved for the successful working of the flexible membrane waterproofing system, Liquid Component and Powder Component. The liquid components acts as an acrylic emulsion and the powder component performs the function of a forming chemicals and fillers with polymer-modified cement. The combination of these two components forms slurry which is applied to the surface area needed to waterproof.

Importance of Waterproofing

Moisture and Humidity knows very well to find its way and seep into the interiors of your place thereby causing significant damage. It is very important to waterproof your home or building from all possible damage.

No waterproofing can lead to the development of cracks, paint peel off and even molds, mildew and air contaminants. It is also a great risk for the structure and foundation of the building. Not only for the building, it can also create health problems for the inhabitants. They also develop a musty smell which gradually increases making it difficult for the inhabitants.

Things to consider

Make sure you choose the best firm for waterproofing. If you select cheap waterproofing contractors you can also expect your work to be of cheap quality.
Before starting the waterproofing work give proper consideration to the area you need to waterproof in order to get an idea on the intensity of work to be done.
The right waterproofing system should be used according to their area of specification. That is, there are certain types of surfaces where crystalline waterproofing system is more suitable than the flexible membrane waterproofing system and vice versa. Though the products are of utmost quality there are fewer chances that you get the desired results.
Use the products before the expiry period. After which the application would not bring any desired results.

It is always recommended to go for those waterproofing companies which are BBB accreditation. In spite of spending a lot on this you deserve to get your waterproofing work last.



WATERGUARD LIQUID MEMBRANE is a single component high performance waterproofing membrane with high elasticity and low water permeability. WATERGUARD LIQUID MEMBRANE is particularly suitable for a wide range of applications including wet areas, foundations, basements, terraces, retaining walls, bridge abutments, planters, inverted roofs and remedial repairs to felt, asphalt, concrete, fibreous cement or other roof structures when protected from exposure to direct sunlight.


  1. Liquid application, easy to apply.
  2.  No Joints.
  3.  High build properties ensure rapid application.
  4.  High elasticity, ensuring a permanently flexible barrier over a wide range of temperatures.
  5.  Thermal stability.
  6.  Excellent adhesion.
  7.  Can be applied to a range of substrates.
  8.  Outstanding resistance to oxidation and brittlement.


WATERGUARD LIQUID MEMBRANE is a highly elastic tough waterproofing system based on modified bitumens water based co-polymer. WATERGUARD LIQUID MEMBRANE is highly resistant to aggressive soils and soluble salts providing an effective continuous barrier and protection against water bourne damage. WATERGUARD LIQUID MEMBRANE is ideally suited as a vapour/salt barrier to building facades behind granite, marble, stone cladding, and curtain wall elements.